AMF Panel

AMF Panel(Auto Man Failure panel) normally connected to the generator set to control the generator set function. Whenever normal supply serve to main switch board failed, the AMF panel will send the power failure signal to generator set. Then the generator set will run and serve the supply to main switch board.

 

Features of AMF Panel

1.                   Used for Controlling Generator function automatically.

2.                   Auto start and Auto stop with 3 Time Cranking with cranking time of 15 sec.

1.                   Available with 63-150 A. single/three phase with Auto changeover.

2.                   PMC based AMF Panel suitable from 5 to 75 KVA DG.

3.                   Contactor base AMF Panel suitable from 10 to 400 KVA DG.

4.                   Relay based AMF Panel suitable from 5 to 63 KVA DG.

5.                   Low/high Voltage & Phase reverse Protection. (optional)

• Item Code: amf10
• Production Capacity: 50
• Delivery Time: 3-5 days
• Packaging Details: Paper box for each panel

We manufacture Electronic AMF Panel based on the latest technology and it is easy to operate and install. Auto main failure panel is used for the automatic operation of the genset. It can be installed up to a maximum distance of 3 meters from the genset and it helps to rotate the starting gear of the genset within 3 seconds after the main supply is cut off. It also works in the same manner when the main supply is restored. In case of the failure at first attempt, it will automatically try to restart after the intervals of 15 seconds for 2 more times.

Features:

• Auto start & Auto Stop Genset.
• Overload automatically shut off supply after 10 seconds.
• The complete harness of connection & bypass connector inbuilt.
• SMPS based battery charger with cut off on a full charge.
• Latest PMC Technology to overcome Switching Spikes & overheating of the coil.
• Available in Single / Three phase Microprocessor based ATS.

We manufacture Electronic AMF Panelbased on the latest technology and it is easy to operate and install. Auto main failure panel is used for the automatic operation of the genset. It can be installed up to a maximum distance of 3 meters from the genset and it helps to rotate the starting gear of the genset within 3 seconds after the main supply is cut off. It also works in the same manner when the main supply is restored. In case of the failure at first attempt, it will automatically try to restart after the intervals of 15 seconds for 2 more times.

Features:

• Auto start & Auto Stop Genset.
• Overload automatically shut off supply after 10 seconds.
• The complete harness of connection & bypass connector inbuilt.
• SMPS based battery charger with cut off on a full charge.
• Latest PMC Technology to overcome Switching Spikes & overheating of the coil.
• Available in Single / Three phase Microprocessor based ATS.

Operating Volt: 140- 280 VAC (P-N)Contactor coil activates only for 1 secAutomatic load transfer among Mains and gensetAuto Start/Auto Stop the Genset when Mains fails/restoresMains input: 3 phase, Gen input: 3 phaseLED Indications for mains (R-Y-B), gen ON, load ON, mode & faultMinimum changeover time to protect sensitive equipmentMains restore delay time: 5 sec, Cranking time: 3-5 sec., Cool down time: 10 secGen output delay time: 8-10 sec, 3 cranking attempts for genset with 15 sec intervalsMicrocontrolled based system with Electrical interlockingAudio visual alarm on common Genset faultsSoft button for Auto/Manual mode selection, manual start/stopBattery charger inbuiltCompatible for new electronic controller based and old key type genset as well.Three pole and Four pole availableCurrent rating 63 Amp. to 150 Amp., suitable for upto 63kVA gensetFabrication: Powder Coated GI Box, Wall mounting, compact sizeWorks well on low / high voltages, no chattering or coil burning, smooth switchingLong life and maintenance freeHeavy duty DMC connection terminal blockScrew tight connection for 63 A. and ring type thimble for 100 and 150 A.Provision for Remote operation (auto/manual, start/stop)

• Production Capacity: 50 unit / day
• Delivery Time: 3-5

Amf Logic Panel use for DG auto start & stop and battery charging.

AMF Panel  for 125 Kva DG SET

200 Amps. 3 Phase ATS with auto Start & Stop

With Auto operation for Three Phase DG &

Three Phase Mains (Double Interlocking)

Panel Size: 700x1200x350 mm  

• Production Capacity: 10 pcs per day
• Packaging Details: Corrugated carton box for each